charlie's na6

[charlie_91]

Biggggg update

So over the past three days ive made a bit of progress and also had a few things not go my way Main thing was finishing off the brakes.. Well i did the fronts all good, but when i went to do the rear i could pull through the new studs.. Turns out there were a little bit too big for the hole. So unfortunately i wasnt able to keep going with that.

Anyways i got the main thing i wanted to do this weekend which was dropping the motor and gearbox in. This was a success

IMG_4316 by charlie_2011, on Flickr


IMG_4319 by charlie_2011, on Flickr

Although we couldnt fit the ppf and the driveshaft due to missing a spacer but thats easily done another day.

All thats left really is to:
- finish off rear brakes
- modify brake like to fit around dump pipe.
- finish intercooler piping
- 3" cat of some sort
- wire tuck

Few little things here and there but its not to much which is good. So happy that i finally have an engine NO MORE FLINSTONE CAR!!!!!

[Dweezle]

LOOKS FREAKIN AMAZING!!!!!

[charlie_91]

thanks

got the missing spacer so i can now put the ppf back in and the drive shaft
also re routed my fuel lines.. gonna need to get the long line under the car shortened though. Organised my intercooler piping to get sorted on saturday so thats a relief.. also trying to figure out which is the best option for my heater hose or whether i should just make up a custom one.. reason being is that its pretty close to the manifold and it might cause problems with the oil drain line..

oh well it will come together soon i hope

[charlie_91]

Update:

So in the last few days ive just been doing a few little fiddly stuff after work.. So far the injectors, rail and fuel lines are hooked up. Just stripped back the old wiring harness and re taped it and ran it differently.. Stoked with the out come. Gonna keep doing the little things i can over the next week or so. Hopefully wont be far off from a tune

Before engine bay.

IMG_0298 by charlie_2011, on Flickr

New wiring etc..

IMG_4323 by charlie_2011, on Flickr

Looking boss

IMG_4324 by charlie_2011, on Flickr

Anyways let me know what u think

[-alex]

Looks great..!
There is green too, how awesome.

[plohl]

looks mad charlie! Serious awesome.

you'll probably be back on the road before I am at this rate!

[charlie_91]

Cheers dude. Still probably 2-3 weeks though. Gonna do my rear studs next week whenever they come then it's gonna go to automotive plus just do a few things and to check over it and make sure it's all good

So close though XD !!!!

[the_darkside]

Epic.

[Mr nanotech]

I like your car jack, what is it?

[charlie_91]

Update:

So today i got my intercooler piping all test fitted and made note of any adjustments we have to make. Really good to get this stuff sorted as its one less thing to worry about This should be finished during the week some time

Also a mate gave me a bellmouth since he isnt using it. So this is what it looks like. I dig it. But i also have an alloy pipe/filter setup to use for street.


IMG_4328 by charlie_2011, on Flickr


IMG_4329 by charlie_2011, on Flickr

[gslender]

But i also have an alloy pipe/filter setup to use for street.

LOL.... Yeah, cause without that "alloy pipe/filter" you'd be illegal on the street....

[charlie_91]

incase i get pulled over. its would be better them seeing that then the bellmouth.

[hks_kansei]

I'd be more concerned about the whole engines not liking twigs, rocks, and other bits of sh*t, getting inside them.

[charlie_91]

thats why u put mesh in front of it ;)

[NitroDann]

Doesnt stop abrasives.

Dann